Panasonic GA-ML Series Manual Download Page 102

Page: 102 / 496

100

5 L2 Features

5.2.5 MAC VLAN

5.2.5

MAC VLAN

Use the following window to implement the settings on a MAC based

VLAN. Then, a static MAC based VLAN entry is configured. If this is

associated with a port, the VLAN operating on the port becomes changed.

Choose

L2 Features > VLAN > MAC VLAN

to display the following

window.

Figure 5-18 MAC VLAN

In the section of

MAC VLAN

, you can configure the following parameters.

Click

Apply

to add new entries based on the information specified.

Click

Delete

to delete the entry.

If two or more pages exist, enter the page numbers. Then click

move to a specific page.

Parameter

Overview

MAC Address

Enter the Unicast MAC address.

VID

Enter the VLAN ID you use. The range is from 1 to
4,094.

Priority

Choose the priority (value) to allocate for untagged-
packets. You can specify the value within the range
from 0 to 7.

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Search results

Summary of Contents for GA-ML Series

Reviews:

Brands by name

Popular brands

Panasonic GA-ML Series, Manual

Search results

Summary of Contents for GA-ML Series

Reviews:

Brands by name

Popular brands