PART 1: CX-Programmer
OMRON
CHAPTER 3 – Project Reference
CX-Programmer _Page 53
The name and comment parts of the operand information can be individually shown or hidden using the Show
checkboxes.
Name
When this option is selected it is possible to set the number of lines to be shown for a symbol name, and whether
they are shown above or below the element (i.e. above or below a contact or coil).
Address
The
If name empty
option will only show the address of an operand if there is no symbol attached to the
address, or if the symbol is unnamed. The
After name
option shows the address after the name, separated by a
comma. The
Above
and
Below
options show the address on a separate line, above or below the element
respectively.
Comment
When this option is selected it is possible to set the number of lines to be shown for a comment, and whether
they are shown above or below the element (i.e. above or below a contact or coil).
Instructions
A range of options are given to determine the information and format of data within instructions.
The
Show data with
option allows a choice of where monitoring data will be shown within the operand box of
an instruction. It can be shown below the name, address or comment of the symbol. It can also share the line of
the name, address or comment, so that the monitoring data is shown before the information on the same line.
This allows the size of the instruction box to be minimized.
Show on right for output instructions
A range of information can be shown on the right of output instructions (i.e. coils and right-hand instructions
such as 'MOV').
The Symbol Comment of the symbol used within the operand can be shown. If this option is set, the comment is
no longer shown inside an output instruction or coil cell.
The Attached Comment (comment property of the instruction element on the diagram) can be shown.
The Instruction Description (shorthand description of the instruction, the same as that shown in the Instruction
dialog) can be shown.
The Operand Description (shorthand description of the operand purpose, the same as that shown in the
Instruction dialog) can be shown.
Special instructions (except intermediate instructions) can also be displayed horizontally (CX-Programmer Ver.
4.0 or later). Enable this function by selecting
Tools – Options
, and then selecting
Show output instructions
Summary of Contents for CX-Programmer 9
