Olivetti OFX 2100 Instruction Manual Download Page 121

Page: 121 / 127

111

SIGNALS AND SERVICE CODES

MEANING

The facsimile machine
does not detect the
dialling tone.

The correspondent’s
number is busy.

The remote fax is not
answering.

Connection error.

Transmission error.

One or more incorrectly
transmitted pages have
not been retran-smitted
automatically.

Call not answered.

An error has been
detected and the
facsimile machine
cannot answer a tele-
phone call.

Document already
used.

The document to be
sent has been deleted.

SOLUTION

Check that the facsimile machine is
connected to the line and retry
connection.

Retry connection.

Contact the correspondent.

Retry transmission. If the error persists,
contact the correspondent.

Retry transmission.

Retry transmitting the pages indicated
on the report as not sent.

Contact the correspondent.

Retry transmission.

The same document cannot be used for
two activities at the same time

Store the document again and repeat
transmission.

OPERATION

Transmission

(all kinds)

Transmission

(from memory)

SERVICE CODES

The table below indicates the service codes that may appear on the reports.

CODE

23, 24, 65

68 - 74, 79

75 - 78

81, 82, 85

1 - 7

cap16.p65

13/04/00, 23.07

111

Summary of Contents for OFX 2100
































































































































Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands

Olivetti OFX 2100, Instruction Manual

Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands