Olivetti OFX 2100 Instruction Manual Download Page 55

Page: 55 / 127

PROGRAMMING

OPERATING

VALUES

YES: Function enabled
NO: Function disabled

9600
19200
38400

ITALIAN
ENGLISH
SPANISH

MEANING

Enables/disables the facsimile
machine for the reception and printing
of a document from the PC.

Enables you to select the serial port
(RS232) communication speed.
Note: If the speed is reduced to 9600
B/S, the transmission speed must be
reduced to 4800 B/S using the
corresponding operating configuration
parameter.

Enables you to choose the language
in which the messages are to be printed
and displayed.

PARAMETER

RX ON PC & FAX

PC COMMUNICATION SPEED

LANGUAGE

F U N C T I O N

6 : C O N F I G U R A T I O N

C O N F I G U R A T I O N

E C M

Press FUNCTION followed by 6.

Press START to access the menu.

Press 3.

The facsimile machine prints all the configuration
parameters.

Press STOP to quit the menu.

Printing can be interrupted by pressing STOP.

PRINTING THE OPERATING CONFIGURATION PARAMETERS

You can print the parameters - set initially and then modified - of the operating configuration at any time.

This section explains how to print them and provides a practical example.

The facsimile machine is on.

cap07.p65

13/04/00, 22.23

Summary of Contents for OFX 2100
































































































































Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands

Olivetti OFX 2100, Instruction Manual

Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands