Olivetti OFX 2100 Instruction Manual Download Page 102

Page: 102 / 127

REPORTS

How to interpret the activity report.

Act. No.

Indicates the activity reference number.

Type

Indicates the type of transaction associated with the document.

Transmission

Reception

Doc. R.

Indicates the specific nature of the document.

ADF

Document sent from the ADF.

Document received and printed.

POLL.

Document received by polling.

000

9999

Document reference number.

Document received during transmission on PC

RDR

Information sent to the remote device during diagnostic session

RDS

Information received from the remote device during diagnostic
session

Identifier

Indicates the correspondent’s facsimile number.

Date/time

Indicates the date and time of transmission/reception.

Length

Indicates the transmission/reception duration. If the values appear
in brackets, this means that several transmission attempts were
made (automatic redial feature).

Page

Indicates the number of pages sent or received.

Result

Indicates the result of transmission/reception.

Transmission/reception successfully completed.

XXXX

(service code) Error occurred during transmission/reception (see
the “SIGNALS AND SERVICE CODES” chapter).

cap13.p65

13/04/00, 22.41

Summary of Contents for OFX 2100
































































































































Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands

Olivetti OFX 2100, Instruction Manual

Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands