Olivetti OFX 2100 Instruction Manual Download Page 52

Page: 52 / 127

PROGRAMMING

PARAMETER

TTI IN SENDER ID

ACTIVITY REPORT

LAST TX REPORT

LAST RX REPORT

LAST ERR. REPORT

BROADCAST REPORT

CLOSED NETWORK RX

CLOSED NETWORK TX

INHIBIT TX

OPERATING

VALUES

YES: TTI included.
NO: TTI excluded.

YES: function enabled
NO: function disabled

YES: printing enabled
NO: printing disabled

YES: limit enabled
NO: limit disabled

YES: Transmission inhibited
NO: Tranmission allowed

MEANING

Includes/excludes the TTI (sender’s
facsimile number and name) in the ID
line.

Enables/disables the facsimile machine
to print the activity report every 30
transactions.

Enables/disables the facsimile machine
to print a report after each transmission
operation.

Enables/disables the facsimile machine
to print a report after each reception
operation.

Enables/disables the facsimile machine
to print a report after each transmission
in which an error occurred.

Enables/disables the facsimile machine
to print a report after each broadcast
transmission operation.

Enables/disables limited reception.
Reception is limited by checking the
last 4 or 6 digits in the sender’s facsimile
number.

Enables/disables limited transmission.
Transmission is limited by checking the
last 4 or 6 digits in the receiver’s facsimile
number.

Inhibits all kinds of transmission. This
function is only valid if the TX password
has been enabled.

cap07.p65

13/04/00, 22.23

Summary of Contents for OFX 2100
































































































































Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands

Olivetti OFX 2100, Instruction Manual

Search results

Summary of Contents for OFX 2100

Reviews:

Related manuals for OFX 2100

Brands by name

Popular brands