Olivetti OFX 2100 Instruction Manual Download Page 103 | Manualshive

Page: 103 / 127

background image

93

REPORTS

POWER FAILURE REPORT

In the event of a power failure or if the facsimile machine’s power switch remains off for more than a day, all
the operations set (for example, a delayed transmission operation) and all the documents stored in the
memory

will be lost. In this case, when the power returns, the facsimile machine will automatically print the power failure
report. This report enables you to recover the information you will need to identify the document and the type
of transaction associated with it.

Example of a power failure report.

cap13.p65

13/04/00, 22.41

93

«
...
101
102
103
104
105
...
»

Summary of Contents for OFX 2100
































































































































Reviews:

No comments

Related manuals for OFX 2100

Brand: Vector Fog Pages: 10

Bernette 340 deco

Brand: Bernina Pages: 2

Brand: Tornado Pages: 11

Brand: Altrad Belle Pages: 46

Brand: GBC Pages: 4

Brand: Janome Pages: 13

Decor Excel 2 5024

Brand: Janome Pages: 41

Brand: DURKOPP ADLER Pages: 90

Streamfeeder Tagger 125 Series

Brand: Thiele Pages: 37

Brand: Brother Pages: 204

Brand: Hitachi Pages: 32

Brand: Hitachi Pages: 48

Brand: Hitachi Pages: 148

Brand: Hitachi Pages: 220

Brand: Hitachi Pages: 16

Auto-Logic KX-F115

Brand: Panasonic Pages: 34

Brand: Panasonic Pages: 74

Facsimile UF-590

Brand: Panasonic Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands