Olivetti OFX 2100 Instruction Manual Download Page 118 | Manualshive

Page: 118 / 127

background image

108

SIGNALS AND ERROR CODES

During reception

SIGNAL

Continuous tone

Audible (continuous tone)
and visual (error LED on)

Audible (intermittent tone)
and visual (error LED on)

DURATION

1 sec.

3 sec.

Permanent

MEANING

Reception successfully
completed

Reception unsuccessful

Handset off hook

SOLUTION

None required

Press STOP to switch off the
LED and check the type of
error on the last reception
report.
Note: this key must not be
pressed when the “TX/
RX”LED is on otherwise
the transmission/reception in
progress will be interrupted.

Hang up and press STOP to
switch off the LED.
Note: this key must not be
pressed when the “TX/
RX”LED is on otherwise the
transmission/reception in
progress will be interrupted.

During a telephone conversation

SIGNAL

Audible (intermittent tone)
and visual (message “TALK”
on the display)

MEANING

Request for a telephone
conversation after
transmission or reception

Request for a telephone
conversation with the fax/
phone switch enabled

DURATION

15 sec.

SOLUTION

Both signals are automati-
cally interrupted after 15
sec.

cap16.p65

13/04/00, 23.07

108

«
...
116
117
118
119
120
...
»

Summary of Contents for OFX 2100
































































































































Reviews:

No comments

Related manuals for OFX 2100

Brand: Singer Pages: 38

Brand: Nagel Pages: 36

Brand: Singer Pages: 46

Powr-Flite M1200-3

Brand: Tacony Pages: 8

Brand: Singer Pages: 14

Brand: BELGACOM Pages: 44

Advolution UHR 70-1700

Brand: Nilfisk-Advance Pages: 32

Folder Express 3001

Brand: Canon Pages: 5

Frozen Gourmet 455

Brand: Crane Pages: 57

SCAN COMBIFLEX 800 PROPAN

Brand: SCANMASKIN Pages: 43

Brand: Newlong Pages: 28

Brand: BoomToneDJ Pages: 8

Brand: BoomToneDJ Pages: 8

Brand: MBM Pages: 20

Brand: OEM Pages: 21

Brand: Rexel Pages: 48

Brand: Robe Pages: 5

Brand: Akiles Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands