Mitsubishi Electric Q80BD-J61BT11N User Manual Download Page 225

Page: 225 / 362

14 - 13 14 - 13

MELSEC

14 COMMUNICATION BETWEEN THE MASTER STATION AND

INTELLIGENT DEVICE STATION (AJ65BT-D75P2-S3)

14.5 Executing the Data Link

To start the data link, first power on the intelligent device station, and then the master
station.

14.5.1 Checking the data link status

The following describes how to check the operation status of the master station and
intelligent device stations under normal data link condition.

(1) Checking the master station

Check the operation status of the master station.

(a) Checking by the LED indication on the CC-Link Ver.2 board

Make sure that the LED status is as follows:

RUN ERR.

No error has occurred.

:ON :OFF

Data are being received.

The CC-Link Ver.2 board is operating normally.

Data are being transmitted.

(b) Checking by the CC-Link Ver.2 Utility

Check that the Board detail information on the CC-Link Ver.2 Utility is
displayed as shown below.

In data link: Normal data link is being performed.

ON (green): The CC-Link Ver.2 board is operating normally.

Normal: The CC-Link Ver.2 board is operating normally.

OFF: No error has occurred.

Summary of Contents for Q80BD-J61BT11N











































































































































































































































































































































































Search results

Summary of Contents for Q80BD-J61BT11N

Reviews:

Related manuals for Q80BD-J61BT11N

Brands by name

Popular brands

Mitsubishi Electric Q80BD-J61BT11N, User Manual

Search results

Summary of Contents for Q80BD-J61BT11N

Reviews:

Related manuals for Q80BD-J61BT11N

Brands by name

Popular brands