Mitsubishi Electric Q80BD-J61BT11N User Manual Download Page 315

Page: 315 / 362

App - 53 App - 53

MELSEC

APPENDIX

Appendix 6 Replacing the CC-Link Board

This appendix describes the CC-Link board replacement procedure and precautions.

Appendix 6.1 Replacing a CC-Link Ver.1 board with a CC-Link Ver.2 board

This section describes how to replace the CC-Link Ver.1 board currently mounted to
the PC with a CC-Link Ver.2 board and precautions to be observed.

Start

↓

Back up the parameters

Activate the "Parameter backup/restoration tool" and back up the
current parameters. (Save to file.).

• • • Appendix 7.1.2 Backing up parameters

↓

Removing the CC-Link Ver.1 board currently in use

Uninstall the software package for the CC-Link Ver.1 board.

Turn OFF the personal computer, and remove the CC-Link Ver.1
board.

↓

Mounting a CC-Link Ver.2 board to be used

Install the software package for the CC-Link Ver.2 board.

• • • Section 7.2 Installation

Install the board to a slot on a personal computer.

• • • Section 5.3.3 Board Installation

Set and check the channel number by the switch.

• • • Section 5.3.4 Channel No. settings

Test the CC-Link Ver.2 board if there is an error in the hardware of
the installed board.

• • • Section 5.7 Test

↓

Restoring parameters

ctivate "Parameter backup/restore tool", and restore the

parameters. (Reading them from files and saving them to the board.)

• • • Appendix 7.1.3 Restoring parameters

↓

End

Summary of Contents for Q80BD-J61BT11N











































































































































































































































































































































































Search results

Summary of Contents for Q80BD-J61BT11N

Reviews:

Related manuals for Q80BD-J61BT11N

Brands by name

Popular brands

Mitsubishi Electric Q80BD-J61BT11N, User Manual

Search results

Summary of Contents for Q80BD-J61BT11N

Reviews:

Related manuals for Q80BD-J61BT11N

Brands by name

Popular brands