MerCruiser Axius 350 MAG User Manual Download Page 31

Page: 31 / 148

Section 2 - Getting to Know Your Power Package

90-899883234 JANUARY 2008

Page 23

• Occupants can be thrown forward due to unexpected loss of forward motion, a

particular concern for passengers in the front of the boat who could be ejected over the

bow and possibly struck by the propulsion or steering components.

• Operator can lose power and directional control in heavy seas, strong current, or high

winds.

• Operator can lose control when docking.

Instrumentation

VESSELVIEW (IF EQUIPPED)

The SmartCraft VesselView is the recommended information source for all drive

information, engine information, fault codes, vessel information, basic navigation data, and

system information.
Refer to the VesselView Operator's Manual for more information.

27198

VesselView

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands