MerCruiser Axius 350 MAG User Manual Download Page 5

Page: 5 / 148

90-899883234 JANUARY 2008

Page i

TABLE OF CONTENTS

Section 1 - Warranty

Warranty Registration: United States and

Canada....................................................................2

Warranty Registration: Outside the United States and

Canada....................................................................2

Transfer of Warranty................................................3

Mercury Product Protection Plan: United States and

Canada....................................................................3

Mercury MerCruiser Limited Warranty

(Gasoline‑Fueled Products Only) ...........................4

3‑Year Limited Warranty Against Corrosion............6

4‑Year Limited Corrosion Warranty: SeaCore

Sterndrive Models with Gas Engines ......................7

Global Warranty Charts...........................................8

Consumer Application Warranty Chart...............8

Commercial Application Warranty Chart.............9

Government Application Warranty Chart..........10

Mercury Installation Quality Certification Program 10

California Emissions Limited Warranty..................11

What Is Covered...............................................11

Duration Of Coverage.......................................12

How To Obtain Warranty Coverage..................12

What Mercury Will Do.......................................13

What Is Not Covered........................................13

Components Of The Emission Control System 13

Disclaimers And Limitations..............................14

California Emission Control Warranty Statement. .14

Your Warranty Rights and Obligations.............14

Manufacturer's Warranty Coverage..................14

Owner's Warranty Responsibilities...................15

Emission Control Information Label.......................15

Owner Responsibility........................................16

Emission Certification Star Label...........................16

Section 2 - Getting to Know Your Power Package

Identification..........................................................20

Engine Serial Number Decal MPI...................20

Bravo Transom Serial Number.......................20

Features and Controls...........................................21

Lanyard Stop Switch......................................21

Emergency Stop (E‑Stop) Switch...................22

Instrumentation...............................................23

VesselView (If Equipped).............................23

SC1000 and SC100 Digital Gauges (If

Equipped).....................................................24

SmartCraft Partner Digital Gauges..............24

Analog Gauges (If Equipped).......................24

Bravo Sterndrive Serial Number and

Identification...................................................25

Electronic Helm Steering................................25

Dual‑Handle Electronic Remote Control (ERC)

with DTS Trackpad Features and Operation. .26

Operation.....................................................26

Adjustment...................................................26

Joystick—Basic Operation.............................27

Power Trim.....................................................27

ERC Trim Control.........................................27

Joystick and Trim Control.............................29

Trailer and Trailer Limit Position..................29

Trim without Key.............................................29

Electrical System Overload Protection...........29

Warning Horn Signals....................................32

Audio Warning System...................................32

Testing The Audio Warning System.............32

Engine Guardian Strategy..............................33

Section 3 - On The Water

Safe Boating Suggestions.....................................36

Be Alert to Carbon Monoxide Poisoning................37

Good Ventilation...............................................38

Poor Ventilation ...............................................38

Basic Boat Operation.............................................38

Drain Plug and Bilge Pump............................38

Freezing Temperature Operation...................39

Protecting People in the Water.......................39

While You Are Cruising................................39

While Boat Is Stationary...............................39

High‑Speed and High‑Performance

Operation........................................................39

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands