MerCruiser Axius 350 MAG User Manual Download Page 96

Page: 96 / 148

Section 5 - Maintenance

Page 88

90-899883234 JANUARY 2008

1. Remove the PCV valve from the port valve cover.

mc71925-1

a -

PCV valve

b -

Hose

2. Disconnect the PCV valve from the hose and discard the valve.
3. Install a new PCV valve in the valve cover and reconnect the hose.
4. Ensure that the PCV valve is tightly seated in the valve cover.

Water‑Separating Fuel Filter (MPI)

Water‑Separating Fuel Filter

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and the lanyard is positioned

so that the engine cannot start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated and avoid prolonged

exposure to vapors. Always check for leaks before attempting to start the engine and

wipe up any spilled fuel immediately.

CAUTION

Failure to release pressure from the fuel system will result in fuel spraying out, which can

cause a fire or explosion. Allow the engine to cool completely and release all fuel pressure

before servicing any part of the fuel system. Always protect eyes and skin from

pressurized fuel and vapors.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands