MerCruiser Axius 350 MAG User Manual Download Page 116

Page: 116 / 148

Section 5 - Maintenance

Page 108

90-899883234 JANUARY 2008

2. Close the seacock, if equipped.

18510

For visual clarity, the secock shown is not installed

a -

Hose fitting to engine

b -

Seacock

c -

Handle (closed position)

d -

To water source pickup attachment

3. If equipped with an alternative water pickup and not equipped with a seacock,

disconnect the water hose from the alternative water pickup and plug both ends,

excluding the Bravo sterndrive.

4. Ensure that the inlet water hose from the sterndrive to the engine is connected.
5. Remove the quick‑connect fitting from the parts bag supplied with the engine.
6. Attach the quick‑connect fitting to a water hose.

18487

a -

Quick connect fitting (water hose

end)

b -

Water hose

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands