MerCruiser Axius 350 MAG User Manual Download Page 90

Page: 90 / 148

Section 5 - Maintenance

Page 82

90-899883234 JANUARY 2008

Changing

1. Remove the gear lube monitor from the bracket.

32539

a -

Gear lube monitor

b -

Typical closed cooled model

c -

Typical seawater cooled model

2. Empty the contents into a suitable container.
3. Install the gear lube monitor in the bracket.
4. Place the sterndrive unit in full trim limit out position, remove the fill and drain screw

and sealing washer and drain the gear lube.

mc79507-1

a -

Fill and drain screw

b -

Sealing washer

5. Remove the vent screw and sealing washer. Allow the gear lube to drain completely.

mc77106-1

a -

Vent screw

b -

Sealing washer

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands