MerCruiser Axius 350 MAG User Manual Download Page 118

Page: 118 / 148

Section 5 - Maintenance

Page 110

90-899883234 JANUARY 2008

17. Disconnect the quick‑connect fitting and water hose from the flush socket on the engine

by pressing the release button on the flush socket.

18488

a -

Quick‑connect fitting (water hose

end)

b -

Flush socket release button

18. Remove the quick‑connect fitting from the water hose.

18487

a -

Quick‑connect fitting (water hose

end)

b -

Water hose

19. Retain the quick‑connect fitting with the water hose end for repeated use by storing it

separately in a storage compartment on the boat for easy access.

IMPORTANT: Do not store the quick‑connect fitting in the flush socket on the engine. Doing

so would allow the seawater pump to suck air during engine operation causing an

overheating problem. Damages due to engine overheating are not covered by Mercury

MerCruiser Warranty.

25900

Quick‑connect fitting stored in the boat

a -

Quick‑connect fitting (water hose end)

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands