MerCruiser Axius 350 MAG User Manual Download Page 87

Page: 87 / 148

Section 5 - Maintenance

90-899883234 JANUARY 2008

Page 79

1. Remove the cap from the heat exchanger and observe the fluid level.

6101

a -

Heat exchanger cap

2. The coolant level in the heat exchanger should be at the bottom of the filler neck. If the

coolant level is low, contact your authorized Mercury MerCruiser dealer.

3. Install the cap onto the heat exchanger.
IMPORTANT: When reinstalling the pressure cap, be sure to tighten it until it seats on the

filler neck.
4. With the engine at normal operating temperature, check the coolant level in the coolant

recovery bottle.

5. The coolant level should be between the "ADD" and "FULL" marks.

6102

6. Add the specified fluid as necessary.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

Filling

NOTICE

Using propylene glycol antifreeze in the closed cooling system can damage the cooling

system or the engine. Fill the closed cooling system with an ethylene glycol antifreeze

solution suitable to the lowest temperature to which the engine will be exposed.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands