MerCruiser Axius 350 MAG User Manual Download Page 98

Page: 98 / 148

Section 5 - Maintenance

Page 90

90-899883234 JANUARY 2008

INSTALLATION

1. Install a new water‑separating fuel filter element into the filter cup. Push the element

into the cup until completely seated.

2. Install new O‑ring on the filter cup.
3. Attach the filter cap to the filter cup by grasping the filter cap and rotating it in a counter

clockwise direction while holding the filter cup stationary, until the filter cap locks

securely into place.

4. Install the fuel filter assembly slowly into the Cool Fuel Module to prevent spilling fuel,

and align the screws retained in the filter cap with the screw holes in the Cool Fuel

Module. Tighten the filter assembly retaining screws until hand tight.

5. Ensure that the filter cap is firmly seated against the Cool Fuel Module and torque each

filter assembly retaining screw.

Description

lb. in.

lb. ft.

Filter assembly retaining screw

6. Open fuel supply valve, if equipped.
7. Reconnect the Cool Fuel Module harness to the engine wiring harness.
8. Properly ventilate the engine compartment.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

9. Supply cooling water to the engine.
10. Start the engine. Check for gasoline leaks around the fuel filter assembly. If leaks exist,

stop the engine immediately. Recheck the filter installation, clean spilled fuel and

properly ventilate the engine compartment. If leaks continue, stop engine immediately

and contact your authorized Mercury MerCruiser dealer.

Lubrication

Electronic Shift Control (ESC) Shift Cable

1. Lubricate the pivot points and the guide contact surfaces.

32233

a -

Pivot points

b -

Shift actuator

c -

Guide contact surfaces

d -

Shift cable

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands