MerCruiser Axius 350 MAG User Manual Download Page 59

Page: 59 / 148

Section 3 - On The Water

90-899883234 JANUARY 2008

Page 51

Joystick Input

Boat Response

Movement

(shown from light gray to dark gray)

24719

Boat moves diagonally

forward and to the port while

rotating counterclockwise

25917

24720

Boat moves to the port while

rotating clockwise

25930

Special Digital Throttle and Shift (DTS) Features

The DTS system features several alternate operational modes for the Electronic Remote

Control (ERC) levers. Any of the listed features can operate simultaneously and can help

you with:
• Warming the engines.
• Synchronizing the engines.
• Accessing the slow‑speed trolling features of the integrated transmission system.

28090

Yacht handled ERC levers with DTS trackpad, Typical

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands