MerCruiser Axius 350 MAG User Manual Download Page 115

Page: 115 / 148

Section 5 - Maintenance

90-899883234 JANUARY 2008

Page 107

10. Observe the water temperature gauge to ensure that the engine is operating in the

normal range.

11. Operate engine with sterndrive in neutral for about 10 minutes or until discharge water

is clear.

12. Slowly return throttle to idle speed position.
13. Stop engine.
14. Shut off the water and remove flushing attachments.
15.

If the boat is out of the water:

Install the water inlet hose to the aft side of the seawater

pump. Tighten the hose clamp securely.

16.

If the boat is in the water:

Tag the ignition switch with an appropriate tag requiring

the seawater inlet hose to be reconnected prior to operating engine.

SeaCore Power Package Flushing Procedure

NOTE: Flushing is needed only for salt, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

IMPORTANT: Flushing the SeaCore power package with the boat and sterndrive in the

water is less effective. Flushing the SeaCore power package is most effective when

performed with the boat and sterndrive out of the water, such as on a boat lift or trailer.

MODELS USING THE STERNDRIVE WATER PICKUP

IMPORTANT: The system is designed to flush the Bravo sterndrive and the engine with

one water source. Do not block or remove the inlet water hose from the sterndrive to the

engine.

NOTE: Engines with the sterndrive water inlet blocked off at the gimbal housing: Refer to

Alternative Water Pickups.

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the

water with a propeller installed. Before installing or removing a propeller, place the drive

unit in neutral and engage the lanyard stop switch to prevent the engine from starting.

Place a block of wood between the propeller blade and the anti‑ventilation plate.

IMPORTANT: Do not allow the engine to pull air or seawater from alternative water pickup

sources during the flushing procedure. If equipped, ensure that all alternative water inlet

hoses are plugged at both ends.
1. Remove the boat from the water.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands