MerCruiser Axius 350 MAG User Manual Download Page 53

Page: 53 / 148

Section 3 - On The Water

90-899883234 JANUARY 2008

Page 45

STARTING THE ENGINE

1. Check all items listed in the Operation Chart.
2. Place the remote control handle in neutral.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

WARNING

Explosive fumes contained in the engine compartment can cause serious injury or death

from fire or explosion. Before starting the engine, operate the bilge blower or vent the

engine compartment for at least five minutes.

NOTE: MerCruiser DTS models are equipped with SmartStart. The SmartStart feature

incorporates push‑button starting. Rather than holding the start button or key switch to start

the engine and then releasing it when the engine starts, SmartStart completely controls

the starting process. When the start button is pushed, the DTS system signals the engine

PCM to start the engine. If the engine does not start, the starting process times out after a

few seconds or when the engine reaches 400 RPM. Attempting to start the engine with the

engine already running will turn the engine off.

3. Turn the ignition key to the "RUN" position.

WARNING

A spinning propeller, a moving boat, or any solid device attached to the boat can cause

serious injury or death to swimmers. Stop the engine immediately whenever anyone in

the water is near your boat.

4. Turn the ignition key switch to the "START" position then release, or depress the start/

stop button and release. If the engine is cold, allow the engine to operate at idle for 6–

10 minutes or until the engine temperature reaches 60° C (140° F).

5. If the engine does not start after three attempts:

Push the throttle‑only button and position the remote control handle or throttle

lever to the 1/4 throttle position.

Turn the ignition key to "start." Release key when the engine starts and allow the

switch to return to the "on" position.

6. If the engine does not start after step 5:

Move the remote control lever to the full throttle position, then return to 1/4 throttle.

Turn the ignition key to "START." Release key when the engine starts and allow

the switch to return to the "on" position.

7. Inspect the power package for fuel, oil, water, and exhaust leaks.
8. Move the control handle with a firm, quick motion forward to shift to forward gear, or

backward to shift to reverse. After shifting, advance throttle to desired setting.

NOTICE

Shifting into gear at engine speeds above idle will damage the drive system. Shift the

drive into gear only when the engine is operating at idle.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands