MerCruiser Axius 350 MAG User Manual Download Page 33

Page: 33 / 148

Section 2 - Getting to Know Your Power Package

90-899883234 JANUARY 2008

Page 25

Item

Gauge

Function

Speedometer

Indicates boat speed.

Tachometer

Indicates engine RPM.

Oil pressure gauge

Indicates engine oil pressure.

Voltmeter

Indicates battery voltage.

Water temperature gauge

Indicates engine operating temperature.

Fuel gauge

Indicates the quantity of fuel in tank.

Hour meter

Records engine operating time.

Bravo Sterndrive Serial Number and Identification

The Bravo sterndrive serial number, gear ratio, model number, and bar code are embedded

in the ground plate on the port side of the sterndrive.

33533

Bravo sterndrive information on ground plate

The serial number is also stamped as a permanent reference on the sterndrive casting

inside the back cover.

33534

Bravo sterndrive serial number stamping

Electronic Helm Steering

The electronic helm steering operates through electronic signals. A computer‑controlled

electric motorsimulates the resistance feedback found in hydraulic steering systems.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands