MerCruiser Axius 350 MAG User Manual Download Page 112

Page: 112 / 148

Section 5 - Maintenance

Page 104

90-899883234 JANUARY 2008

Dual Water Pick‑up Flush Gearcase Seal Kit

91‑881150K 1

9194

Blocks off the front water inlet holes on the dual water inlet

gearcases.

STERNDRIVE WATER PICKUPS

There are two types of water pickups available on Mercury MerCruiser sterndrives: dual

water, and side water pickups. Dual water pickups require the flushing attachment (44357Q

2) and the flush seal kit (881150K 1), and side water pickups require the flushing

attachment (44357Q 2).

5752

5773

Dual water pickup

Side water pickup

NOTE: Flushing is needed only for salty, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

NOTICE

Flushing the engine with the boat in the water can cause seawater to flow into the engine,

resulting in engine damage. Close the seacock before flushing the engine. Keep the

seacock closed until starting the engine.

1. On seawater cooled models: Proceed to Step 4. or Step 5.
2. On models with the sterndrive seawater inlet blocked, supply water to the sterndrive

and to the engine. See

Alternative Water Pickups

3. On models using the sterndrive seawater inlet and a through‑hull or through‑transom

alternative water pickup, supply water to only the sterndrive by taking the following

steps to block, or disconnect and block, the hose from the alternative seawater pickup

pump inlet Y‑fitting.
a.

If equipped with a seacock, close the seacock in the hose from the alternative

water pickup.

If not equipped with a seacock, disconnect the hose from the alternative water

pickup and plug both ends.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands