MerCruiser Axius 350 MAG User Manual Download Page 142

Page: 142 / 148

Section 7 - Troubleshooting

Page 134

90-899883234 JANUARY 2008

Possible Cause

Remedy

Seawater pickups or sea strainer obstructed.

Remove obstruction.

Faulty thermostat.

Replace.

Coolant level (if equipped) low in closed cooling

section.

Check for cause of low coolant level and repair. Fill

system with proper coolant solution.

Heat Exchanger or Fluid Cooler plugged with foreign

material

Clean Heat Exchanger, Engine Oil Cooler, and

Transmission Oil Cooler (if equipped).

Loss of pressure in closed cooling section.

Check for leaks. Clean, inspect and test pressure cap.

Faulty seawater pickup pump.

Repair.

Seawater discharge restricted or plugged.

Clean exhaust elbows.

Insufficient Engine Temperature

Possible Cause

Remedy

Faulty thermostat.

Replace.

Low Engine Oil Pressure

Possible Cause

Remedy

Insufficient oil in crankcase.

Check and add oil.

Excessive oil in crankcase (causing it to become

aerated).

Check and remove required amount of oil. Check for

cause of excessive oil (improper filling).

Diluted or improper viscosity oil.

Change oil and oil filter, using correct grade and

viscosity oil. Determine cause for dilution (excessive

idling).

Battery Will Not Recharge

Possible Cause

Remedy

Excessive current draw from battery.

Turn off non‑essential accessories.

Alternator drive belt loose or in poor condition.

Replace and/or adjust.

Unacceptable battery condition.

Test battery, replace if necessary.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires

(especially battery cables). Clean and tighten faulty

connections. Repair or replace damaged wiring.

Faulty alternator

Test alternator output, replace if necessary.

Joystick

Symptom

Remedy

The joystick does not control the boat.

One or both remote controls are not in neutral. Put

both remote controls in neutral.
One or both engines are not running. Start the engine

or engines.

Response to joystick input is erratic, or the joystick

operates independent of input.

Ensure there are no radios or other sources of

electronic or magnetic interference near the joystick.

The joystick does not function properly and a fault

code is set.

Check VesselView for Guardian fault codes that

indicate reduced engine power. If found, have the

system checked by your authorized Mercury

MerCruiser dealer.

The joystick does not work; No fault code is set and

cruise control engaged.

Disengage cruise control.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands