MerCruiser Axius 350 MAG User Manual Download Page 47

Page: 47 / 148

Section 3 - On The Water

90-899883234 JANUARY 2008

Page 39

Freezing Temperature Operation

IMPORTANT: If the boat is operated during periods of freezing temperature, precautions

must be taken to prevent freeze damage to the power package. Damage caused by

freezing is not covered by Mercury MerCruiser Limited Warranty.

Protecting People in the Water

WHILE YOU ARE CRUISING

It is very difficult for a person in the water to take quick action to avoid a boat heading in

their direction, even at slow speeds.

21604

Always slow down and exercise extreme caution any time you are boating in an area where

there might be people in the water.
Whenever a boat is moving (even coasting) and the gear shift is in neutral, there is sufficient

force by the water on the propeller to cause the propeller to rotate. This neutral propeller

rotation can cause serious injury.

WHILE BOAT IS STATIONARY

WARNING

A spinning propeller, a moving boat, or any solid device attached to the boat can cause

serious injury or death to swimmers. Stop the engine immediately whenever anyone in

the water is near your boat.

Shift into neutral and shut off the engine before allowing people to swim or be in the water

near your boat.

High‑Speed and High‑Performance Operation

If your boat is considered a high‑speed or high‑performance boat with which you are

unfamiliar, we recommend that you never operate it at its high speed capability without first

requesting an initial orientation and demonstration ride with your dealer or an operator

experienced with your boat. For additional information, refer to

Hi-Performance Boat

Operation

booklet (90‑849250‑R2) from your dealer, distributor or Mercury Marine.

Passenger Safety in Pontoon Boats and Deck Boats

Whenever the boat is in motion, observe the location of all passengers. Do not allow any

passengers to stand or use seats other than those designated for traveling faster than idle

speed. A sudden reduction in boat speed, such as plunging into a large wave or wake, a

sudden throttle reduction, or a sharp change of boat direction, could throw them over the

front of boat. Falling over the front of the boat between the two pontoons will position them

to be run over.

BOATS HAVING AN OPEN FRONT DECK

No one should ever be on the deck in front of the fence while the boat is in motion. Keep

all passengers behind the front fence or enclosure.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands