MerCruiser Axius 350 MAG User Manual Download Page 107

Page: 107 / 148

Section 5 - Maintenance

90-899883234 JANUARY 2008

Page 99

Description

Location

Figure

Gearcase anode plate

Underside of the lower gearcase

20336

Ventilation plate anode

Front of the gearcase

20338

MerCathode System

The MerCathode electrode is mounted

to the underside of the gimbal housing.

The MerCathode controler is mounted

on the engine or on the boat transom.

The controler harness connects to the

electrode harness.

20340

Anode kit (if equipped)

The boat transom

20341

Trim cylinder anodes

Mounted on each of the trim cylinders

20342

Propshaft anode (Bravo Three)

Bbehind the aft propeller

20344

Checking the Quicksilver MerCathode System

The MerCathode system should be tested to ensure adequate output. Perform the test

where boat is moored, using the reference electrode and test meter. Contact your

authorized Mercury MerCruiser dealer for service and information .

Reference Electrode

91‑76675T 1

9188

Senses and electrical current in the water when testing the

MerCathode system. Use to check hull potential.

Power Package Exterior Surfaces

1. Spray the entire power package at recommended intervals with Corrosion Guard.

Follow the instructions on the can for proper application.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands