MerCruiser Axius 350 MAG User Manual Download Page 130

Page: 130 / 148

Section 6 - Storage

Page 122

90-899883234 JANUARY 2008

12. Before launching the boat, pull up on the manual release valve. Verify that the green

indicators are no longer extended.

6135

a -

Green indicators

Manual Single‑Point Drain System

BOAT IN THE WATER

1. Close the seacock (if equipped) or remove and plug the water inlet hose.
2. Rotate the blue handle counterclockwise until it stops (approximately two turns). The

red on the handle shaft indicates that the drain system is open. Do not force the handle

as this will create new threads.

3. Immediately remove the blue drain plug from the side of the thermostat housing. This

must be removed within 30 seconds to properly vent the cooling system.

6136

a -

Blue handle

b -

Blue drain plug location

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands