MerCruiser Axius 350 MAG User Manual Download Page 88

Page: 88 / 148

Section 5 - Maintenance

Page 80

90-899883234 JANUARY 2008

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will

overheat and suffer damage. Provide a sufficient supply of water to the water inlets during

operation.

NOTICE

Air trapped in the closed cooling system can cause the engine to overheat, resulting in

engine damage. Minimize the possibility of trapping air when initially filling the closed

cooling system by positioning the boat so that the front of the engine is higher than the

rear of the engine.

NOTE: Add coolant only when engine is at normal operating temperature.

1. Remove the fill cap from the coolant recovery bottle.
2. Fill to the "FULL" line with the specified coolant.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

3. Install the fill cap onto the coolant recovery bottle.

Changing

Contact your authorized Mercury MerCruiser dealer.

Sterndrive Gear Lube

Checking

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by

law. Use caution not to spill oil, coolant, or other fluids into the environment when using

or servicing your boat. Be aware of the local restrictions governing the disposal or

recycling of waste, and contain and dispose of fluids as required.

NOTE: The level of gear lube oil will fluctuate during operation. Check the oil level with the

engine cold, before starting.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands