MerCruiser Axius 350 MAG User Manual Download Page 28

Page: 28 / 148

Section 2 - Getting to Know Your Power Package

Page 20

90-899883234 JANUARY 2008

Identification

The serial numbers are the manufacture's keys to numerous engineering details which

apply to your MerCruiser power package. When contacting MerCruiser about service,

always specify model and serial numbers.

Engine Serial Number Decal MPI

The serial number decal is located on the engine cover.

25903

Serial numbers and maintenance color codes decal

The engine serial number is also stamped in the engine block.

Bravo Transom Serial Number

The Bravo transom serial number is stamped in the U‑bolt plate of the Bravo transom

assembly.

25904

a -

Transom serial number

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands