MerCruiser Axius 350 MAG User Manual Download Page 82

Page: 82 / 148

Section 5 - Maintenance

Page 74

90-899883234 JANUARY 2008

Engine Oil

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by

law. Use caution not to spill oil, coolant, or other fluids into the environment when using

or servicing your boat. Be aware of the local restrictions governing the disposal or

recycling of waste, and contain and dispose of fluids as required.

Checking

1. Stop the engine. Allow approximately 5 minutes for the oil to drain into the oil pan. The

boat must be at rest in the water.

2. Remove the dipstick. Wipe clean and reinstall fully into the dipstick tube. Wait 60

seconds to allow trapped air to vent.

NOTE: Ensure that dipstick is installed with oil level indication marks facing the rear of the

engine (flywheel end).

6095

a -

Dipstick tube

IMPORTANT: Add the specified engine oil to bring the level up to, but not over, the full or

OK range mark on the dipstick.
3. Remove the dipstick and observe the oil level. Oil level must be between full or OK

range and add. Reinstall dipstick into dipstick tube.

Filling

IMPORTANT: Do not overfill the engine with oil.
IMPORTANT: Always use the dipstick to determine the exact quantity of oil or fluid required.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands