MerCruiser Axius 350 MAG User Manual Download Page 141

Page: 141 / 148

Section 7 - Troubleshooting

90-899883234 JANUARY 2008

Page 133

Engine Will Not Start or Is Hard to Start

Possible Cause

Remedy

Lanyard stop switch activated.

Check the lanyard stop switch.

Improper starting procedure.

Read the starting procedure.

Insufficient fuel supply.

Fill fuel tank or open valve.

Faulty ignition system component.

Service the ignition system.

Clogged fuel filter.

Replace fuel filter.

Stale or contaminated fuel.

Drain fuel tank. Fill with fresh fuel.

Fuel line or tank vent line kinked or clogged. Replace kinked lines or blow out lines with compressed air to

remove obstruction.

Faulty wire connections.

Check wire connections.

EFI system fault.

Have EFI System checked by an authorized Mercury

MerCruiser dealer.

Poor Performance

Possible Cause

Remedy

Throttle not fully open.

Inspect the throttle cable and linkages for proper operation.

Damaged or improper propeller.

Replace the propeller.

Excessive bilge water.

Drain and check for cause of entry.

Boat overloaded or load improperly

distributed.

Reduce load or redistribute load more evenly.

Flame arrestor dirty.

Clean the flame arrestor.

Boat bottom fouled or damaged.

Clean or repair as necessary.

Ignition problem.

See

Engine Runs Rough, Misses or Backfires

Engine overheating.

See

Excessive Engine Temperature

EFI System fault

Have EFI System checked by an authorized Mercury MerCruiser

dealer.

Engine Runs Rough, Misses, or Backfires

Possible Cause

Remedy

Clogged fuel filter.

Replace filter.

Stale or contaminated fuel.

If contaminated, drain tank. Fill with fresh fuel.

Kinked or clogged fuel line or fuel tank vent line. Replace kinked lines or blow out lines with compressed air

to remove obstruction.

Flame Arrestor dirty.

Clean Flame Arrestor.

Faulty ignition system component.

Service ignition system.

Idle speed too low.

Have EFI system checked by an authorized Mercury

MerCruiser dealer.

EFI System fault.

Have EFI System checked by an authorized Mercury

MerCruiser dealer.

Excessive Engine Temperature

Possible Cause

Remedy

Water inlet or seacock closed.

Open.

Drive belt loose or in poor condition.

Replace or adjust belt.

Summary of Contents for Axius 350 MAG





















































































































































Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands

MerCruiser Axius 350 MAG, User Manual

Search results

Summary of Contents for Axius 350 MAG

Reviews:

Related manuals for Axius 350 MAG

Brands by name

Popular brands