MerCruiser Axius 350 MAG User Manual Download Page 61 | Manualshive

Page: 61 / 148

background image

Section 3 - On The Water

90-899883234 JANUARY 2008

Page 53

THROTTLE ONLY

31465

"THROTTLE ONLY" button

To engage Throttle Only mode:
1. Place both ERC levers in neutral.
2. Press the "THROTTLE ONLY" button, located on the DTS trackpad.
3. The "THROTTLE ONLY" button light illuminates and the neutral lights blink.
4. Place either ERC lever into gear.
5. The RPM of the engines can be increased, while the transmissions remains in Neutral.

NOTE: Pressing the "THROTTLE ONLY" button while the ERC levers are in gear, turns

off the button light, but the boat remains in throttle only mode until you place the levers in

neutral.

To disengage throttle only mode:
1. Bring both ERC levers to neutral. Throttle only will not disengage unless the ERC levers

are in neutral.

2. Press the "THROTTLE ONLY" button. The "THROTTLE ONLY" button light turns off.
3. The neutral lights remains on.

«
...
59
60
61
62
63
...
»

Summary of Contents for Axius 350 MAG





















































































































































Reviews:

No comments

Related manuals for Axius 350 MAG

Brand: BAFANG Pages: 5

Brand: BAFANG Pages: 12

Brand: Admiral Pages: 9

Brand: Jula Pages: 17

Calzoni MR Series

Brand: Parker Pages: 50

Brand: Sanshin Pages: 25

Brand: Yanmar Pages: 52

Brand: Siemens Pages: 20

Brand: Siemens Pages: 26

Brand: Siemens Pages: 40

Brand: Siemens Pages: 87

Brand: Siemens Pages: 96

Brand: Siemens Pages: 116

Brand: Siemens Pages: 156

Brand: Siemens Pages: 252

Brand: ETQ Pages: 89

Brand: Baumer Hübner Pages: 20

Brand: Seg Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands