Mercedes-Benz 2016 Command Operating Instructions Manual Download

Page: 32 / 222

Adjusting the volume for phone calls

You can adjust the volume for hands-free

mode during a telephone call.

Turn the thumbwheel to the right of the

controller.

Press the

button on the mul-

tifunction steering wheel.

Setting the volume for the Voice Control

System voice output, see the separate

operating instructions.

Switching the sound on or off

Media source sound

Press the thumbwheel to the right of the

controller.

Press the

button on the multifunction

steering wheel.

If the audio output is switched off, the

status line will show the

symbol. If

you switch the media source or change the

volume, the sound is automatically

switched on.

Switching navigation announcements

off and on again

To switch off navigation announce-

ments: press the thumbwheel to the right

of the controller during the announcement.

The

Spoken driving recommendations

have been deactivated.

message

appears.

To switch navigation announcements

back on: switch COMAND off and then on

again (

page 29).

Start a new route calculation (

page 69).

Select

: while route guidance is active,

show the menu and press the controller

(

page 87).

Basic menu displays

Press the

button or the

, or

button.

Navigation: the map displays the current

vehicle position.
Radio: the basic menu of the last radio

mode set appears.
Media: the basic display for the last media

source set appears. In the example, SD

memory card mode is set.
Communication: the basic menu of the

last communication function set appears.
Vehicle functions: the basic display

appears.

To show the menu: slide

the con-

troller.

The menu for the selected functions

appears. Depending on the operation, the

Basic functions

Overview

and

ation

Summary of Contents for 2016 Command































































































































































































































Search results

Summary of Contents for 2016 Command

Reviews:

Related manuals for 2016 Command

Brands by name

Popular brands

Mercedes-Benz 2016 Command, Operating Instructions Manual

Search results

Summary of Contents for 2016 Command

Reviews:

Related manuals for 2016 Command

Brands by name

Popular brands