Lenovo ThinkSystem SR550 Maintenance Manual Download Page 93

Page: 93 / 206

1. Remove the top cover. See “Remove the top cover” on page 56.
2. Remove all the installed drives and drive fillers (if any) from the drive bays. See “Remove a hot-swap

drive” on page 74.

To remove the backplane, complete the following steps:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

Figure 62. 2.5-inch-drive backplane removal

Step 1. Lift the release tabs and pivot the backplane backward slightly to release it from the two pins on the

chassis.

Step 2. Lift the backplane out of the chassis carefully.
Step 3. Disconnect cables from the backplane.

If you are instructed to return the old backplane, follow all packaging instructions and use any packaging
materials that are provided.

Install the 2.5-inch-drive backplane

Use this information to install the 2.5-inch-drive backplane.

Chapter 3

Hardware replacement procedures

Summary of Contents for ThinkSystem SR550















































































































































































































Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands

Lenovo ThinkSystem SR550, Maintenance Manual

Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands