Lenovo ThinkSystem SR550 Maintenance Manual Download Page 102 | Manualshive

Page: 102 / 206

background image

S035

CAUTION:
Never remove the cover on a power supply or any part that has this label attached. Hazardous voltage,
current, and energy levels are present inside any component that has this label attached. There are no
serviceable parts inside these components. If you suspect a problem with one of these parts, contact
a service technician.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

S001

DANGER

Electrical current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:

• Connect all power cords to a properly wired and grounded electrical outlet/source.

• Connect any equipment that will be attached to this product to properly wired outlets/sources.

• When possible, use one hand only to connect or disconnect signal cables.

• Never turn on any equipment when there is evidence of fire, water, or structural damage.

• The device might have more than one power cord, to remove all electrical current from the

device, ensure that all power cords are disconnected from the power source.

Figure 70. Hot-swap power supply label on the cover

94

ThinkSystem SR550 Maintenance Manual

«
...
100
101
102
103
104
...
»

Summary of Contents for ThinkSystem SR550















































































































































































































Reviews:

No comments

Related manuals for ThinkSystem SR550

Brand: GE Pages: 5

BT-CK 18 2B-1.5 Kit

Brand: Taurus Pages: 40

Brand: Valcom Pages: 3

Standard iControl

Brand: Nordson Pages: 6

SMA 50 BER-13.G1

Brand: Gerima Pages: 24

Brand: XPOtool Pages: 12

Brand: General integration Pages: 12

360 IQ HAT PRESS

Brand: Hotronix Pages: 16

Brand: Neilsen Pages: 16

LIFESTAR 20-1000TUL-DC

Brand: Vanner Pages: 14

Brand: CHP Pages: 8

Brand: FTI Pages: 9

Powervar 3400 Series

Brand: Ametek Pages: 68

Brand: H3C Pages: 6

Brand: SATA Pages: 28

Brand: Cocraft Pages: 40

Brand: Yamato Pages: 25

Brand: Matco Tools Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands