manualshive.com logo in svg

Lenovo ThinkSystem SR550, Maintenance Manual

The Lenovo ThinkSystem SR550 is a powerful and reliable server designed for optimal performance and flexibility. Unlock its full potential by accessing its comprehensive user manual, available for free download at our website. Experience hassle-free installation and setup, all while maximizing productivity and efficiency.

Share
Download
background image

Figure 119. Assembling a PHM in the shipping tray

a.  Align the triangular marks on the processor retainer and the heat sink or align the triangular mark on 

the processor retainer with the notched corner of the heat sink.

b.  Insert the processor-retainer clips into the holes on the heat sink.
c.  Press the retainer into place until the clips at all four corners engage.

To install a PHM, complete the following steps:

Watch the procedure

A video of this procedure is available at 

https://www.youtube.com/playlist?list=PLYV5R7hVcs- 

C9jFjZnXQ6AmTXaIdX6_HJ

. 

Step 1.  Remove the processor socket cover, if one is installed on the processor socket, by placing your 

fingers in the half-circles at each end of the cover and lifting it from the system board.

Step 2.  Install the processor-heat-sink module on the system board. 

150

ThinkSystem SR550 Maintenance Manual

Summary of Contents for ThinkSystem SR550















































































































































































































Reviews:

No comments

Related manuals for ThinkSystem SR550

V-TAC 80133970 Instruction Manual preview
80133970
Brand: V-TAC Pages: 16
Ofs Mya Assembly Instructions preview
Mya
Brand: Ofs Pages: 3
Parkside RAPIDFIRE Translation Of The Original Instructions preview
RAPIDFIRE
Brand: Parkside Pages: 64
EINHELL TE-MG 200 E Original Operating Instructions preview
TE-MG 200 E
Brand: EINHELL Pages: 24
Pulsar PSBEN 2024B/LCD Manual preview
PSBEN 2024B/LCD
Brand: Pulsar Pages: 44
EGAmaster 57535 Operating Instructions Manual preview
57535
Brand: EGAmaster Pages: 10
Stuart Boostamatic 4000 Operating Instructions Manual preview
Boostamatic 4000
Brand: Stuart Pages: 20
OMERA OPI M-400 Operation And Maintenance Manual preview
OPI M-400
Brand: OMERA Pages: 50
Manhattan 168205 User Manual preview
168205
Brand: Manhattan Pages: 16
ZALMAN ZM750-ARX User Manual preview
ZM750-ARX
Brand: ZALMAN Pages: 24
Caillau Clic Instruction Manual preview
Clic
Brand: Caillau Pages: 14
Larson Electronics ITX-40 Instruction Manual preview
ITX-40
Brand: Larson Electronics Pages: 2
Mengual VIRUTEX FP114 Operating Instructions Manual preview
VIRUTEX FP114
Brand: Mengual Pages: 68
Central Machinery 63471 Owner'S Manual & Safety Instructions preview
63471
Brand: Central Machinery Pages: 16
Gardner Bender SDT-3 Operating Instructions preview
SDT-3
Brand: Gardner Bender Pages: 2
SereneLife PSLTLL1812 User Manual preview
PSLTLL1812
Brand: SereneLife Pages: 12
Nitronic ST730T Operating Manual preview
ST730T
Brand: Nitronic Pages: 54
Populo RTK-107 User Manual preview
RTK-107
Brand: Populo Pages: 28

Brands by name

Popular brands

Load more brands