Lenovo ThinkSystem SR550 Maintenance Manual Download Page 173 | Manualshive

Page: 173 / 206

background image

1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left

inside your server.

2. Properly route and secure the cables in the server. Refer to the cable connecting and routing information

for each component.

3. If you have removed the top cover, reinstall it. See “Install the top cover” on page 58.
4. Reconnect external cables and power cords to the server.

Attention:

To avoid component damage, connect the power cords last.

5. Update the server configuration if necessary.

• Download and install the latest device drivers:

http://datacentersupport.lenovo.com

• Update the system firmware. See “Firmware updates” on page 9.
• Use the Lenovo XClarity Provisioning Manager to update the UEFI configuration. For more

information, see:

http://sysmgt.lenovofiles.com/help/topic/LXPM/UEFI_setup.html

• Use the Lenovo XClarity Provisioning Manager to configure the RAID if you have installed or removed

a hot-swap drive, a RAID adapter, or the M.2 backplane and M.2 drive. For more information, see:

http://sysmgt.lenovofiles.com/help/topic/LXPM/RAID_setup.html

Note:

Make sure the latest version of ThinkSystem M.2 with Mirroring Enablement Kit Firmware is applied to

avoid virtual disk/array missing after system board replacement.

.

Hardware replacement procedures

165

«
...
171
172
173
174
175
...
»

Summary of Contents for ThinkSystem SR550















































































































































































































Reviews:

No comments

Related manuals for ThinkSystem SR550

Brand: Parkside Pages: 64

Brand: Parkside Pages: 44

Brand: Parkside Pages: 64

Brand: Paslode Pages: 20

Brand: Vanderbilt Pages: 18

Brand: MaxPro PROFESSIONAL Pages: 50

Brand: Whyte Pages: 12

Brand: Vaterra Pages: 4

Brand: Wacker Neuson Pages: 112

Brand: TekPower Pages: 4

Brand: APS Pages: 156

Brand: Intec Controls Pages: 3

Brand: MESTA Pages: 26

Brand: probst Pages: 28

Brand: Delta Pages: 4

Powervar 3400 Series

Brand: Ametek Pages: 68

Brand: Echo Pages: 44

Brand: Gallagher Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands