Lenovo ThinkSystem SR550 Maintenance Manual Download Page 150

Page: 150 / 206

Figure 112. TCM/TPM adapter removal

If you are instructed to return the old TCM/TPM adapter, follow all packaging instructions and use any
packaging materials that are provided.

Install the TCM/TPM adapter (for Chinese Mainland only)

Use this information to install the TCM/TPM adapter.

Static Sensitive Device

Ground package before opening”

on page 56

To install the TCM/TPM adapter, complete the following steps:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

Step 1. Touch the static-protective package that contains the new TCM/TPM adapter to any unpainted

surface on the outside of the server. Then, take the new TCM/TPM adapter out of the package and
place it on a static-protective surface.

Step 2. Insert the TCM/TPM adapter into the TCM/TPM connector on the system board.

142

ThinkSystem SR550 Maintenance Manual

Summary of Contents for ThinkSystem SR550















































































































































































































Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands

Lenovo ThinkSystem SR550, Maintenance Manual

Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands