Lenovo ThinkSystem SR550 Maintenance Manual Download Page 109

Page: 109 / 206

Step 3. If there is a power supply filler installed, remove it.

Figure 75. Hot-swap power supply filler removal

Step 4. Slide the new hot-swap power supply into the bay until the release latch clicks into place.

Figure 76. Hot-swap power supply installation

After installing the power supply:

1. Connect one end of the power cord to the new power supply connector; then, connect the other end of

the power cord into a properly grounded electrical outlet.

2. If the server is powered off, power on the server. Ensure that both the power input LED and the power

output LED on the power supply are lit, indicating that the power supply is operating properly.

RAID super capacitor module replacement

Use this information to remove and install a RAID super capacitor module.

Chapter 3

Hardware replacement procedures

101

Summary of Contents for ThinkSystem SR550















































































































































































































Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands

Lenovo ThinkSystem SR550, Maintenance Manual

Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands