manualshive.com logo in svg

Lenovo ThinkSystem SR550, Maintenance Manual

The Lenovo ThinkSystem SR550 is a powerful and reliable server designed for optimal performance and flexibility. Unlock its full potential by accessing its comprehensive user manual, available for free download at our website. Experience hassle-free installation and setup, all while maximizing productivity and efficiency.

Share
Download
background image

Remove the TCM/TPM adapter (for Chinese Mainland only)

Use this information to remove the TCM/TPM adapter.

“

Read 

the  

installation 

Guidelines” on 

page 53

“

Power off  

the server  

for this task” 

on page 13

“

ATTENTION:  

Static Sensitive Device  

Ground package before opening” 

on page 56

To remove the TCM/TPM adapter, complete the following steps:

Watch the procedure

A video of this procedure is available at 

https://www.youtube.com/playlist?list=PLYV5R7hVcs- 

C9jFjZnXQ6AmTXaIdX6_HJ

. 

Step 1.  Remove the top cover. See “Remove the top cover” on page 56.
Step 2.  Locate the TCM/TPM connector on the system board. See the “System board components” on 

page 27. 

Step 3.  Press the release latch on the TCM/TPM adapter, and lift it straight up. 

Notes: 

•  Carefully handle the TCM/TPM adapter by its edges.
•  Your TCM/TPM adapter might look slightly different from the illustration. 

Chapter 3

.

Hardware replacement procedures

141

Summary of Contents for ThinkSystem SR550















































































































































































































Reviews:

No comments

Related manuals for ThinkSystem SR550

Makita 6825 Instruction Manual preview
6825
Brand: Makita Pages: 20
Makita 6821 Parts Breakdown preview
6821
Brand: Makita Pages: 2
Harley Benton Powerplant Owner'S Manual preview
Powerplant
Brand: Harley Benton Pages: 16
U-Line RIPACK 3000 Assembly Instructions Manual preview
RIPACK 3000
Brand: U-Line Pages: 15
EIBENSTOCK EHR 20 / 2.6 S SET Original Instructions Manual preview
EHR 20 / 2.6 S SET
Brand: EIBENSTOCK Pages: 64
King Industrial CT-204 Service Manual preview
CT-204
Brand: King Industrial Pages: 7
Sanela SLZ 07 Mounting Instructions preview
SLZ 07
Brand: Sanela Pages: 2
Scheppach 5906808915 Original Operating Manual preview
5906808915
Brand: Scheppach Pages: 48
ECO POWER SBP-XFMR Series Installation And User Instructions Manual preview
SBP-XFMR Series
Brand: ECO POWER Pages: 21
SNOWJOE sunjoe24V-HG100 Operator'S Manual preview
sunjoe24V-HG100
Brand: SNOWJOE Pages: 52
Valex Painting machine Instruction Manual And Safety Instructions preview
Painting machine
Brand: Valex Pages: 20
Xantrex XPower Powerpack 300 Owner'S Manual preview
XPower Powerpack 300
Brand: Xantrex Pages: 60
Banner MPS-15 Specifications preview
MPS-15
Brand: Banner Pages: 2
Bahco Torque Screwdrivers BE-6990-AH Specification preview
Torque Screwdrivers BE-6990-AH
Brand: Bahco Pages: 2
Parkside 270411 Operation And Safety Notes preview
270411
Brand: Parkside Pages: 55
Grizzly G0834 Owner'S Manual preview
G0834
Brand: Grizzly Pages: 60
3B SCIENTIFIC PHYSICS 1008692 Instruction Sheet preview
1008692
Brand: 3B SCIENTIFIC PHYSICS Pages: 24
Greenlee GATOR EK06ATCL Operation Manual preview
GATOR EK06ATCL
Brand: Greenlee Pages: 12

Brands by name

Popular brands

Load more brands