manualshive.com logo in svg

Lenovo ThinkSystem SR550, Maintenance Manual

The Lenovo ThinkSystem SR550 is a powerful and reliable server designed for optimal performance and flexibility. Unlock its full potential by accessing its comprehensive user manual, available for free download at our website. Experience hassle-free installation and setup, all while maximizing productivity and efficiency.

Share
Download
background image

Remove the system board

Use this information to remove the system board.

“

Read 

the  

installation 

Guidelines” on 

page 53

“

Power off  

the server  

for this task” 

on page 13

“

ATTENTION:  

Static Sensitive Device  

Ground package before opening” 

on page 56

Attention:

Disconnect all power cords for this task.

Before removing the system board: 

1.  Remove the top cover. See “Remove the top cover” on page 56.
2.  Record where the cables are connected to the system board; then, disconnect them.  

Attention:

Disengage all latches, cable clips, release tabs, or locks on cable connectors beforehand. 

Failing to release them before removing the cables will damage the cable connectors on the system 
board. Any damage to the cable connectors may require replacing the system board.

3.  Remove any of the following components that are installed on the system board and put them in a safe, 

static-protective place. See the related topics in this chapter. 

•  Air baffle
•  System fans
•  Processor and heat sink module (PHM) 

Note:

Do not disassemble the PHM.

•  Riser assembly
•  DIMMs
•  LOM adapter
•  TCM/TPM (for Chinese Mainland only)
•  M.2 module
•  PCIe adapter
•  CMOS battery

4.  Pull out the power supplies a little bit. Ensure that they are disconnected from the system board.

To remove the system board, complete the following steps:

Watch the procedure

A video of this procedure is available at 

https://www.youtube.com/playlist?list=PLYV5R7hVcs- 

C9jFjZnXQ6AmTXaIdX6_HJ

. 

156

ThinkSystem SR550 Maintenance Manual

Summary of Contents for ThinkSystem SR550















































































































































































































Reviews:

No comments

Related manuals for ThinkSystem SR550

KAKA Industrial AP-3 Operation Manual preview
AP-3
Brand: KAKA Industrial Pages: 10
jbc DSS Instruction Manual preview
DSS
Brand: jbc Pages: 12
OBO Bettermann PDP-PS Mounting Instructions preview
PDP-PS
Brand: OBO Bettermann Pages: 2
MULTIQUIP R2000 Operation And Parts Manual preview
R2000
Brand: MULTIQUIP Pages: 90
Campbell Hausfeld IN715601AV Operating Instructions Manual preview
IN715601AV
Brand: Campbell Hausfeld Pages: 32
Fellowes esi FCH4C-BLK Assembly Instructions Manual preview
esi FCH4C-BLK
Brand: Fellowes Pages: 12
Campbell Hausfeld DG460500CK Operating Instructions And Parts Manual preview
DG460500CK
Brand: Campbell Hausfeld Pages: 10
WAGO 750-613/040-000 Manual preview
750-613/040-000
Brand: WAGO Pages: 52
Timberline Tool TRTW1 Instruction Manual preview
TRTW1
Brand: Timberline Tool Pages: 8
Ingersoll-Rand QiP Series Product Information preview
QiP Series
Brand: Ingersoll-Rand Pages: 56
Steel City 40540 User Manual preview
40540
Brand: Steel City Pages: 32
FTI KC 10 Series Installation And Maintenance Instructions Manual preview
KC 10 Series
Brand: FTI Pages: 9
Parkside KH 3041 AIR STAPLER SET Operation And Safety Notes preview
KH 3041 AIR STAPLER SET
Brand: Parkside Pages: 37
National Instruments SCXI-1383 Installation Manual preview
SCXI-1383
Brand: National Instruments Pages: 11
Stanley POWERMAX 6 Instructions preview
POWERMAX 6
Brand: Stanley Pages: 2
Spirent HellermannTyton E4500 Instructions For Use Manual preview
HellermannTyton E4500
Brand: Spirent Pages: 8
Edge Craft Diamond Hone 601 Instructions Manual preview
Diamond Hone 601
Brand: Edge Craft Pages: 12
VERTO 52G057 Instruction Manual preview
52G057
Brand: VERTO Pages: 64

Brands by name

Popular brands

Load more brands