Lenovo ThinkSystem SR550 Maintenance Manual Download Page 128 | Manualshive

Page: 128 / 206

background image

S009

CAUTION:
To avoid personal injury, disconnect the fan cables before removing the fan from the device.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

Remove a system fan

Use this information to remove the system fan.

Guidelines” on

for this task”

Static Sensitive Device

Ground package before opening”

Before removing a system fan:

1. Remove the top cover. See “Remove the top cover” on page 56.
2. Remove the air baffle. See “Remove the air baffle” on page 60.

To remove a system fan, complete the following steps:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

120

ThinkSystem SR550 Maintenance Manual

«
...
126
127
128
129
130
...
»

Summary of Contents for ThinkSystem SR550















































































































































































































Reviews:

No comments

Related manuals for ThinkSystem SR550

Brand: KAKA Industrial Pages: 10

Brand: RAMSET Pages: 16

Brand: Tanco Pages: 26

Brand: XPOtool Pages: 10

Brand: Whyte Pages: 12

650 Watt ATX Power Supply

Brand: Ultra Pages: 9

Brand: Parkside Pages: 80

Brand: Fein Pages: 95

GE-CS 18 Li-Solo

Brand: EINHELL Pages: 44

Brand: Valex Pages: 12

Brand: Gern Pro Pages: 25

Brand: Black Box Pages: 2

Brand: 2E Pages: 28

Brand: IMI NORGREN Pages: 11

Brand: Mac allister Pages: 27

Brand: Phenix Pages: 15

Brand: Bosch Pages: 279

Brand: Bosch Pages: 337

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands