Lenovo ThinkSystem SR550 Maintenance Manual Download Page 39

Page: 39 / 206

Figure 15. System board LEDs

Table 11. LEDs on the system board

Callout

System error LED

System ID LED

XCC heartbeat LED

Field-Programmable Gate Array (FPGA) error LED

System power LED

Internal cable routing

Some of the components in the server have internal cables and cable connectors.

To connect cables, observe the following guidelines:

• Power off the server before you connect or disconnect any internal cables.
• See the documentation that comes with any external devices for additional cabling instructions. It might

be easier for you to route cables before you connect the devices to the server.

Chapter 2

Server components

Summary of Contents for ThinkSystem SR550















































































































































































































Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands

Lenovo ThinkSystem SR550, Maintenance Manual

Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands