Lenovo ThinkSystem SR550 Maintenance Manual Download Page 131

Page: 131 / 206

Before removing the system fan cage:

1.  Remove the top cover. See “Remove the top cover” on page 56.
2.  Remove the air baffle. See “Remove the air baffle” on page 60.
3.  If you are replacing the system fan cage, remove all system fans first. See “Remove a system fan” on

page 120. If you are removing the system fan cage to access other components, you can remove it with
the system fans installed.

To remove the system fan cage, complete the following steps:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

Figure 97. System fan cage removal

Step 1. Remove the screws that secure the system fan cage to the chassis from the exterior of the chassis.
Step 2. Grasp the system fan cage and carefully lift it out of the chassis.

If you are instructed to return the old system fan cage, follow all packaging instructions and use any
packaging materials that are provided.

Install the system fan cage

Use this information to install the system fan cage.

Chapter 3

Hardware replacement procedures

123

Summary of Contents for ThinkSystem SR550















































































































































































































Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands

Lenovo ThinkSystem SR550, Maintenance Manual

Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands