Lenovo ThinkSystem SR550 Maintenance Manual Download Page 112

Page: 112 / 206

Figure 79. Connecting the RAID super capacitor module to the RAID adapter

Complete the parts replacement. See “Complete the parts replacement” on page 164.

Riser card replacement

Use this information to remove and install a riser card.

Note:

The following procedure is based on the scenario that the riser card is installed on the riser card

bracket 1. The procedure is similar for riser card installed on the riser card bracket 2.

Remove a riser card

Use this information to remove a riser card.

Static Sensitive Device

Ground package before opening”

on page 56

Before removing a riser card, remove the top cover. See “Remove the top cover” on page 56.

To remove a riser card, complete the following steps:

Watch the procedure

A video of this procedure is available at

https://www.youtube.com/playlist?list=PLYV5R7hVcs-

C9jFjZnXQ6AmTXaIdX6_HJ

Step 1. Disconnect related cables.
Step 2. Grasp the riser assembly by its edges and carefully lift it straight up and off the chassis.

104

ThinkSystem SR550 Maintenance Manual

Summary of Contents for ThinkSystem SR550















































































































































































































Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands

Lenovo ThinkSystem SR550, Maintenance Manual

Search results

Summary of Contents for ThinkSystem SR550

Reviews:

Related manuals for ThinkSystem SR550

Brands by name

Popular brands