Lenovo 7D1J Reference Download Page 186

Page: 186 / 246

Severity: Error

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable device driver, firmware update, version of service

information for this product or other information that applies to this error. Load new device driver and
any required firmware updates.

2. If this device and/or any attached cables were recently installed, moved, serviced or upgraded.

a. Reseat Adapter and any attached cables.

b. Reload Device Driver.

c. If device is not recognized, reconfiguring slot to Gen1 or Gen2 may be required. Gen1/Gen2

settings can be configured via F1 Setup -> System Settings -> Devices and I/O Ports ->PCIe
Gen1/Gen2/Gen3 Speed Selection, or the OneCLI utility.

d. If aPCIe error has also been reported on a second slot within the same node, please ensure steps

a, b, and c above are also performed for that adapter before proceeding.

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFIO0013I: The device found at Bus [arg1] Device [arg2] Function [arg3] could not be

configured due to resource constraints. The Vendor ID for the device is [arg4] and the Device ID is
[arg5]. The physical slot number is [arg6].

Severity: Warning

User Action:

Complete the following steps:

1. If this PCIe device and/or any attached cables were recently installed, moved, serviced or upgraded,

reseat adapter and any attached cables.

2. Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update

that applies to this error.(NOTE: It may be necessary to disable unused option ROMs from UEFI F1
setup, OneCLI utility, or using adapter manufacturer utilities so that adapter firmware can be
updated.)

3. Move the adapter to a different slot. If a slot is not available or error recurs, replace the adapter.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

•

FQXSFIO0014J: A bad option ROM checksum was detected for the device found at Bus [arg1]

Device [arg2] Function [arg3]. The Vendor ID for the device is [arg4] and the Device ID is [arg5]. The
physical slot number is [arg6].

Severity: Error

User Action:

Complete the following steps:

1. If thisPCIe device and/or any attached cables were recently installed, moved, serviced or upgraded.

Reseat adapter and any attached cables.

2. Move adapter to a different system slot, if available.

3. Check Lenovo support site for any applicable service bulletin or UEFI or adapter firmware update

that applies to this error.

182

ThinkSystem DA240 Enclosure and ThinkSystem SD630 V2 Compute Node Messages and Codes Reference

Summary of Contents for 7D1J























































































































































































































































Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands

Lenovo 7D1J, Reference

Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands