Lenovo 7D1J Reference Download Page 170 | Manualshive

Page: 170 / 246

background image

1. Update the BMC firmware.

2. NOTE: Some cluster solutions require specific code levels or coordinated code updates. If the device

is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.

3. If problem persists, collect Service Data log.

4. Contact Lenovo Support.

•

FQXSPUP4001I: Flash of [arg1] from [arg2] succeeded for user [arg3] .

This message is for the use case where a user has successfully flashed the firmware component (MC Main
Application, MC Boot ROM, BIOS, Diagnostics, System Power Backplane, Remote Expansion Enclosure
Power Backplane, Integrated System Management).

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0035

User Action:

Information only; no action is required.

•

FQXSPUP4002I: Flash of [arg1] from [arg2] failed for user [arg3].

This message is for the use case where a user has not flashed the firmware component from the interface
and IP address due to a failure.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0036

User Action:

Information only; no action is required.

•

FQXSPUP4003I: [arg1] firmware mismatch internal to system [arg2]. Please attempt to flash the

[arg3] firmware.

This message is for the use case where a specific type of firmware mismatch has been detected.

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0042

User Action:

Complete the following steps until the problem is solved:

1. AC cycle the system.

2. Reflash XCC/BMC firmware to the latest version.

166

ThinkSystem DA240 Enclosure and ThinkSystem SD630 V2 Compute Node Messages and Codes Reference

«
...
168
169
170
171
172
...
»

Summary of Contents for 7D1J























































































































































































































































Reviews:

No comments

Related manuals for 7D1J

Brand: IBM Pages: 180

UniServer T1100 G3

Brand: H3C Pages: 66

UniServer R6900 G3

Brand: H3C Pages: 214

UniServer R6700 G3

Brand: H3C Pages: 151

UniServer R4900 G5

Brand: H3C Pages: 16

APSolute Vision

Brand: Radware Pages: 81

Brand: d3 Technologies Pages: 10

Brand: TYAN Pages: 77

Brand: Moxa Technologies Pages: 100

Brand: Axis Pages: 85

Brand: Cavalry Pages: 16

PRIMERGY Econel 230R S1

Brand: Fujitsu Pages: 53

Primergy ECONEL 100 S2

Brand: Fujitsu Pages: 8

PRIMERGY Econel 200 S2

Brand: Fujitsu Pages: 65

PRIMERGY MX130 S1

Brand: Fujitsu Pages: 85

PRIMERGY Econel 100

Brand: Fujitsu Pages: 64

Brand: Fujitsu Pages: 105

Brand: Fujitsu Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands