manualshive.com logo in svg

Lenovo 7D1J, Reference

Get the ultimate reference manual for the Lenovo 7D1J at our website. This comprehensive user manual is available for free download, providing detailed instructions on how to maximize the potential of your device. Enhance your user experience by accessing the manual directly from our manualshive.com.

Share
Download
background image

• 

FQXSFMA0023M: Error has occurred in NVDIMM flash. NVDIMM backup/restore may not operate 

correctly. [arg1] 

Severity: Error

User Action:

Complete the following steps:  

1.  Reseat the affected NDIMM, and the DIMM in the adjacent slots if populated.

2.  Check Lenovo support site for an applicable service bulletin or firmware update that applies to this 

memory error.

3.  If the problem persists, collect Service Data logs.

4.  Contact Lenovo Support.

• 

FQXSFMA0024M: Error has occurred in NVDIMM Supercap. NVDIMM backup/restore may not 

operate correctly. [arg1] 

Severity: Error

User Action:

Complete the following steps:  

1.  If the server has recently been installed, moved, serviced, or upgraded, verify that the DIMM is 

properly seated and visually verify that there is no foreign material in any DIMM connector on that 
memory channel.

2.  If no problem is observed on the BBU connectors or the problem persists, Check the Lenovo support 

site for an applicable service bulletin or firmware update that applies to this memory error.

3.  If the problem persists, collect Service Data logs.

4.  Contact Lenovo Support.

• 

FQXSFMA0025M: NVDIMM Supercap has been disconnected. NVDIMM will lose its backup ability 

until this is corrected. [arg1] 

Severity: Error

User Action:

Complete the following steps:  

1.  If the server has recently been installed, moved, serviced, or upgraded, verify that the DIMM is 

properly seated and visually verify that there is no foreign material in any BBU connector on that 
memory channel.

2.  If no problem is observed on the BBU connectors or the problem persists, Check the Lenovo support 

site for an applicable service bulletin or firmware update that applies to this memory error.

3.  If the problem persists, collect Service Data logs.

4.  Contact Lenovo Support.

• 

FQXSFMA0026I: DIMM [arg1] Self-healing, attempt post package repair (PPR) at Rank [arg2] Sub 

Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. [arg7] 

Severity: Info

User Action:

Information only; no action is required. 

• 

FQXSFMA0027K: Invalid memory configuration (Unsupported DIMM Population) detected. Please 

verify memory configuration is valid.[arg1] 

Severity: Error

Chapter 4

.

UEFI events

191

Summary of Contents for 7D1J























































































































































































































































Reviews:

No comments

Related manuals for 7D1J

NEC NECCare Gold Express5800/320Fd Service Manual preview
NECCare Gold Express5800/320Fd
Brand: NEC Pages: 10
NEC SV8500 Setup Manual preview
SV8500
Brand: NEC Pages: 84
NEC NEC Express5800 Series Release Note preview
NEC Express5800 Series
Brand: NEC Pages: 6
Premio FlacheSAN1L-D4 Quick Manual preview
FlacheSAN1L-D4
Brand: Premio Pages: 3
7starlake ROC286B User Manual preview
ROC286B
Brand: 7starlake Pages: 32
BlueBroadcaster iSENDER User Manual preview
iSENDER
Brand: BlueBroadcaster Pages: 21
NETGEAR ReadyNAS 3220 Series Datasheet preview
ReadyNAS 3220 Series
Brand: NETGEAR Pages: 4
SmartSight S1600e User Manual preview
S1600e
Brand: SmartSight Pages: 113
disguise rx Hardware Manual preview
rx
Brand: disguise Pages: 12
Fujitsu PRIMERGY TX1310 M1 Operating Manual preview
PRIMERGY TX1310 M1
Brand: Fujitsu Pages: 66
Fujitsu PRIMERGY T850 System Configurator And Order-Information Manual preview
PRIMERGY T850
Brand: Fujitsu Pages: 18
Fujitsu PRIMERGY TX1320 M1 Operating Manual preview
PRIMERGY TX1320 M1
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY TX120 S3 Operating Manual preview
PRIMERGY TX120 S3
Brand: Fujitsu Pages: 82
Fujitsu PRIMERGY TX1310 M3 Operating Manual preview
PRIMERGY TX1310 M3
Brand: Fujitsu Pages: 68
Fujitsu PRIMERGY TX1310 M1 Upgrade And Maintenance Manual preview
PRIMERGY TX1310 M1
Brand: Fujitsu Pages: 232
Fujitsu PRIMERGY TX120 S2 Operating Manual preview
PRIMERGY TX120 S2
Brand: Fujitsu Pages: 78
Fujitsu PRIMERGY TX1310 M5 Upgrade And Maintenance Manual preview
PRIMERGY TX1310 M5
Brand: Fujitsu Pages: 265
Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual preview
PRIMERGY TX1320 M1
Brand: Fujitsu Pages: 340

Brands by name

Popular brands

Load more brands