manualshive.com logo in svg

Lenovo 7D1J, Reference

Get the ultimate reference manual for the Lenovo 7D1J at our website. This comprehensive user manual is available for free download, providing detailed instructions on how to maximize the potential of your device. Enhance your user experience by accessing the manual directly from our manualshive.com.

Share
Download
background image

• 

FQXSPMA0009I: Memory sparing initiated for [PhysicalMemoryElementName] on Subsystem 

[MemoryElementName]. 

This message is for the use case when an implementation has detected that Memory double chip sparing 
has been initiated.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 
CIM Prefix: PLAT CIM ID: 0140

User Action:

Information only; no action is required.

• 

FQXSPMA0010J: [PhysicalMemoryElementName] on Subsystem [MemoryElementName] 

Throttled. 

This message is for the use case when an implementation has detected Memory has been Throttled.

Severity: Warning
Serviceable: Yes
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: PLAT CIM ID: 0142

User Action:

Complete the following steps:  

1.  Check the event log of XClarity Controller for any fan- or cooling-related issues.

2.  Make sure that the airflow at the front and rear of the enclosure is not obstructed and that fillers are in 

place, clean and correctly installed.

3.  Make sure that the room temperature is within operating specifications. 

4.  If the problem persists and there are no other DIMMs with the same indication, replace the DIMM.

• 

FQXSPMA0011G: Memory Logging Limit Reached for [PhysicalMemoryElementName] on 

Subsystem [MemoryElementName]. 

This message is for the use case when an implementation has detected that the Memory Logging Limit 
has been Reached.

Severity: Warning
Serviceable: Yes
Automatically notify Support: Yes
Alert Category: Warning - Memory
SNMP Trap ID: 43
CIM Prefix: PLAT CIM ID: 0144

User Action:

Complete the following steps:  

1.  If the compute node has recently been installed, moved, serviced, or upgraded, verify that the DIMM 

is properly seated and visually verify that there is no foreign object in any DIMM connector on that 
memory channel. If either of these conditions is found, correct and retry with the same DIMM. (Note: 
The event Log might contain a recent FQXSFMA0011I event denoting a change is detected in DIMM 
population that could cause this problem.)

92

ThinkSystem DA240 Enclosure and ThinkSystem SD630 V2 Compute Node Messages and Codes Reference

Summary of Contents for 7D1J























































































































































































































































Reviews:

No comments

Related manuals for 7D1J

Lantronix UDS2100 Quick Start Manual preview
UDS2100
Brand: Lantronix Pages: 6
Lantronix SGX 5150 Manual preview
SGX 5150
Brand: Lantronix Pages: 27
3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print... User Manual preview
3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...
Brand: 3Com Pages: 94
HGST Ultrastar Serv24 S2122-N24-4 Installation Manual preview
Ultrastar Serv24 S2122-N24-4
Brand: HGST Pages: 36
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
Valcom VIP-201 Specification preview
VIP-201
Brand: Valcom Pages: 4
IBM @server x Series Quick Setup Manual preview
@server x Series
Brand: IBM Pages: 8
Samsung SNT-1010 Specifications preview
SNT-1010
Brand: Samsung Pages: 1
Samsung MIM-D00 Installation Manual preview
MIM-D00
Brand: Samsung Pages: 28
Samsung SNT-1010 User Manual preview
SNT-1010
Brand: Samsung Pages: 51
Samsung SMARTSERVER 370 User Manual preview
SMARTSERVER 370
Brand: Samsung Pages: 72
Samsung TC222L User Manual preview
TC222L
Brand: Samsung Pages: 94
Samsung IPX-S300B System Description preview
IPX-S300B
Brand: Samsung Pages: 162
Samsung Webthru SWC 306 User Manual preview
Webthru SWC 306
Brand: Samsung Pages: 33
Samsung MIM-D00 User Manual preview
MIM-D00
Brand: Samsung Pages: 52
Samsung SmartServer 3840 Installation Manual preview
SmartServer 3840
Brand: Samsung Pages: 67
Sony WG-C20 Series Quick Start Manual preview
WG-C20 Series
Brand: Sony Pages: 3
Sony 158WGC10A Quick Start Manual preview
158WGC10A
Brand: Sony Pages: 7

Brands by name

Popular brands

Load more brands