Lenovo 7D1J Reference Download Page 91

Page: 91 / 246

Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0244

User Action:

Complete the following steps:

1. Check the Lenovo support site for an applicable service bulletin or firmware update for the system or

adapter that applies to this error.

2. If the problem persists, collect the Service Data log.

3. Contact Lenovo Support.

•

FQXSPIO0014J: Bus [SensorElementName] is operating in a degraded state.

This message is for the use case when an implementation has detected a Bus is Degraded.

Severity: Warning
Serviceable: Yes
Automatically notify Support: No
Alert Category: Warning - Other
SNMP Trap ID: 60
CIM Prefix: PLAT CIM ID: 0246

User Action:

Complete the following steps to solve:

1. Reseat the adapter or move to the other slot.

2. If the problem still exists, then replace the adapter.

3. If the problem still exists, then contact Lenovo support.

•

FQXSPIO0015M: Fault in slot [PhysicalConnectorSystemElementName] on system

[ComputerSystemElementName].

This message is for the use case when an implementation has detected a Fault in a slot.

Severity: Error
Serviceable: Yes
Automatically notify Support: Yes
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0330

User Action:

Complete the following steps to fix the error:

1. Make sure that all I/O expansion adapters have correct and matching levels of device drivers and

firmware.

2. Check the event log of XClarity Controller for additional information about failing components. Check

http://support.lenovo.com/ for TECH tips or firmware updates that might correct the error.

3. If there are no entries related to the error in the event log, contact Lenovo support.

•

FQXSPIO2002I: The System [ComputerSystemElementName] has detected a POST Error

deassertion.

This message is for the use case when an implementation has detected that Post Error has deasserted.

Severity: Info

Chapter 3

XClarity Controller events

Summary of Contents for 7D1J























































































































































































































































Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands

Lenovo 7D1J, Reference

Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands